In this study, the linear structural relationship model’s slope parameter is determined by using the proposed robust nonparametric method based on trimmed mean. This method is an upgrade to the nonparametric method that was put forward by Al-Nasser and Ebrahem (2005) by employing trimmed mean for all likely paired slopes rather than median slopes. Simulation study and real data were used to compare the proposed method’s performance versus the traditional maximum likelihood method. In the simulation study, based on both methods’ mean square error, it was inferred that the MLE method breaks down due to the presence of outliers even though its functioning was not affected when there was no outlier in the data set. Based on the real life example, it can be concluded that the performance of our proposed method was quite well in determining slope parameter
Amel Saad Alshargawi, (1-2022)

Abstract Laser surface treatment of materials is one of the most effective methods of improving properties and performance of metallic articles. This technique proved its capabilities and advantages in comparison with other methods of surface treatment As an example, it has been shown that the distortion caused by this type of treament is at least one order of magnitude smaller than by that due to other techniques. Moreeover, laser beam is capable of reaching practically any point of the surface whatever it is narrow or difficult to reach by other techniques. The current work investigates the possibility of improving certain mechanical properties of both technically pure aluminum and A1-4o/oSi alloy, using ruby laser of 3 xl 05 W/cm2 power density. The surface of the investigated materials has been impregnated by SiC particles of varying size ranges, with or without firrther alloying of the surface with Titanium powder addition to the impregnated mixture. The laser treatment included coating one surface of each specimen of SiC particles by means of a binder added at a certain ratio (with or without Ti additions to the mixture). The coated surface was then subjected to the laser beam, which melted a layer I OO-150Jilll thick. Due to hydrodynamic effects the melt mixes with SiC particles and dissolves some or all of the added Ti and rapidly solidifies forming a thin layer distinct in properties from the original surface. Two groups of specimens were used in this study. The first group was treated by impregnating SiC particles of one size range with or without Ti-additions. Various numbers of laser pulses have been applied increasmg in a geometrical progression (1-2-4-8 pulses). These specimens were used for the study of the effect of varying: 1) the chemical composition of the substrate materials ;2) the number of laser pulses :and 3) the effect of Ti additions to the impregnating mixture on the microstracture and microhardness of the treated zones. The specimens of the 2nd group were coated by a square network of laser treated zones each 1.5mm in diameter. These specimens have been used to study :1) the effect of the chemical composition of the substrate material ;2) the size of the SiC particles and 3) the effect of Ti addition to the mixture on the wear perfomance of the treated specimens. Identical specimens have been used to determine the solubility of Si into the aluminum phase during the test by means of x-ray diffraction. This dissolved Si is partly responsible for the increase ID microhardness and wear resistance of the investigated specimens. The results show the positive effect of the applied treatment on the properties and preformence of technically pure AI and A-4%Si alloy. The materials microhardness within the treated zones has been increased by a factor of 2.7 and 2.4 for pure Al and Al-4%Si substrates, respectively. The microstructure of the treated zones became more homogeneous and the penetration of SiC particles into them has been increased with increasing the number of the applied laser pulses. The wear resistance of pure Al has been increased by a factor of 73.6 due to laser assisted impregnation, while that of AI-4%Si by afactor of 42.5. Wear resistance was found to increase with I) Si addition to the base metal; 2) Ti addition to the impregnated mixture, and 3) increasing the SiC particle size. This thesis is a part of a wider study that deals with surface treatment of Al and AI-Si alloys undertaken in our laboratry. Such study proved how effective the laser alloying and impregnation of such alloys in improving some of their mechanical properties which are important in industrial application, especially in internal combustion engine design.
أسماء عبد الرزاق وهرة (2002)

Abstract Libyan cities have experienced a period of rapid urban expansion in the past decades. Urban growth as an example has been the focus of urban researches for a long time. Due to the complexity of the urban growth process, it’s very difficult to model urban growth using traditional urban models. Recently, urban researches are keen on a new technology, Remote Sensing. Remote Sensing technique was applied in many aspects of life, due to ability of covering and representing the real world around us. In urban research, field researches set up many applications to simulate the urban phenomena such as sprawl process, landuse change trends, landcover...etc. Remote sensing technology helps to extract and organize the data about such phenomenon. In addition to understand their spatial relationships, and provides a powerful means to planners and decision makers for analyzing and information about a place or a phenomenon. This will have great impact on the quality of the decision-making. The study uses Spot 5 images, topographic maps which derived from aerial photographs for the year 1980. The remote sensing image interpretation and change detection to review the urban expansion for the study area in (1980 and 2009).Spot satellite image of 2009 and Landuse maps1980 will be used to derive information on urban land use in the study area. The visual interpretation is used to extract landuse. The mutual use of Remote Sensing (RS) and Geographic Information System (GIS) describes the overall physics changes of the study area. This effort can be considered as an application case in this field (RS-based town planning information system), where this thesis show how that system can be useful of using this technology and supporting the sector by developing a model that can support the process of planning and maintain what remained of the agricultural lands to prevent them from encroachment by the urban growth.
حسين علي أحمد زيدان (2010)